【 PREMIUM STANDARD 】

● SSL-compatible programmable servo

* Compatible with CODE 10 (M17S, EXZES ZⅢ, M17, MT-5, MT-R,

M12S(RS), EXZES ZZ, MT-44)

Not compatible with CODE 5 (M12, EXZES Z, MT-4S, MT-4, MT-S)

● Compatible with MULTI SETTING GEAR

● Supports Extreme Response (SXR) mode

● Supports Ultra Response (SUR) mode

● Supports Super Response (SSR) mode

● Supports High Response (SHR) mode

● Compatible with 2-cell Li-Po batteries

● Low-profile servo

● High-speed type

● Full aluminum case

● Coreless motor

● Full metal gears

Speed

0.08sec/60°(7.4V)

0.10sec/60°(6.0.V)

Torque

16.6kg・cm(7.4V)

14.7kg・cm(6.0V)

Size

40.5x20.5x26.5mm

Weight

56.8g

Shock Tower that raises the shock mounting height by approximately 1mm compared to the standard kit specification.
Optimizes shock travel when using the 1.5mm Aluminum Chassis (TS095) or Steel Chassis (TS096).

Shock Tower that raises the shock mounting height by approximately 1mm compared to the standard kit specification.
Optimizes shock travel when using the 1.5mm Aluminum Chassis (TS095) or Steel Chassis (TS096).

Shock Tower that raises the shock mounting height by approximately 1mm compared to the standard kit specification.
Optimizes shock travel when using the 1.5mm Aluminum Chassis (TS095) or Steel Chassis (TS096).

Shock Tower that raises the shock mounting height by approximately 1mm compared to the standard kit specification.
Optimizes shock travel when using the 1.5mm Aluminum Chassis (TS095) or Steel Chassis (TS096).

Dedicated Upper Bulkhead for Lower Bulkhead (+2mm)

Dedicated Upper Bulkhead for Lower Bulkhead (+2mm)

    Lower Bulkhead that allows the differential (spool) pulley height to be raised by 2mm compared to the standard kit specification.
This allows you to optimize the differential (spool) height when using the 1.5mm Aluminum Chassis (TS095) or Steel Chassis (TS096).
Note: Dedicated Upper Bulkheads (TS173 / TS174) are required.

Lower Bulkhead that allows the differential (spool) pulley height to be raised by 2mm compared to the standard kit specification.
This allows you to optimize the differential (spool) height when using the 1.5mm Aluminum Chassis (TS095) or Steel Chassis (TS096).
Note: Dedicated Upper Bulkheads (TS173 / TS174) are required.

Utilizing heavy-duty brass material effectively concentrates the center of gravity toward the lower chassis, delivering stable handling especially on high-grip surfaces. Features a sleek black finish.

O-Ring for a Tighter Fit in the Ball Socket (TS005)
Made from a specially formulated, slightly harder material to maintain a consistent fit and feel over extended use.

Stiffening the rear chassis flex of the IF14 Speciale improves traction.
Chassis flex can also be fine-tuned by changing the mounting screw positions and the number of screws used.
Compatible with the 1.5mm Aluminum Chassis (TS095) and Steel Chassis (TS096).
Not compatible with the Carbon Chassis (TS093) and 2.0mm Aluminum Chassis (TS094).

Upstop Set for limiting suspension arm up travel.
Allows fine-tuning of vehicle dynamics by adjusting the front and rear suspension arm up travel
Easily adjustable from the top of the chassis using a 1.5mm hex wrench.
Compatible with the 1.5mm Aluminum Chassis (TS095) and Steel Chassis (TS096).
Not compatible with the Carbon Chassis (TS093) and 2.0mm Aluminum Chassis (TS094).

Specifications:

Dimensions 39 x 26 x 10 mm

Weight 8.0 g

Frequency 2.4 GHz S-FHSS

Compatibility 3PRKA / 2PL / 3PL / 4PL

Channels 4ch

Power Supply 4.8–7.4 V (dry cell batteries cannot be used)

Connector Futaba standard connector

A special tool machined from aluminum that allows for more efficient maintenance of the Front ECS EVO driveshaft (TS182).
Not only does it ensure the universal joint nut (TS185) is securely tightened, but it also holds the universal joint ring (TS186) in place, making it easy to remove the universal joint nut.